Bespoke worktops service at Norfolk Oak means pretty much anything you can imagine that can be done with a wooden worktop. Bespoke doesn't just mean sink cut outs, it can be oversized breakfast bars, large curves or complete circles - bespoke wooden worktops to any shape and size. Below is a list of the 'standard' options we offer. If you have more specific requirements in mind or would like to receive a complete quotation please visit our Receiving A Bespoke Worktops Quotation page for more information.
If you would like the reassurance of us oiling your wooden worktops ready for you to install or if you simply don’t have the time or means to do this yourself, we offer an oiling service. We oil both sides of the worktops, around 6 coats, so they are ready for immediate installation. Whilst it cannot be left in a damp environment, a wooden worktop which has Pre-Installation Oiling can be left a while before fitting.
Once the worktop is in, the top and exposed edges will require further coats, around 6, and additional hand sanding to achieve the full protection and beautiful finish. With our oiling service you are automatically supplied with the correct quantities of oil needed to finish the worktop.
Costs start at £ 35 per linear metre.
Of course if you would prefer just to buy the oil it is £ 15 a litre, which is enough to finish one three metre long wooden worktop.
Wooden upstands provide a wonderful aesthetic to the back edge of your kitchen worktop. However the secret benefit of wooden upstands is covering up all sorts of problems; walls which aren't straight, corners which are never quite 90 degrees. Fixing wooden upstands has been made simple with the advent of 'no more nails' glue - push the wooden upstand into place, hold firmly for a couple of minutes and that's it.
We make our wooden upstands in two styles; 'Wide Block Upstands' with joints along the length - suited to our Classic Wide Block worktops, and 'Super Stave Upstands' in continuous lengths with no joints - suited to our Super Stave and Traditional Plank wooden worktops.
| Wide Block Style Wooden Upstands |
Super Stave Style Wooden Upstands |
|
|---|---|---|
| 1 metre | £ 23 | £ 32 |
| 2 metres | £ 41 | £ 59 |
| 3 metres | £ 57 | £ 84 |
Our wooden upstands are available in 1 metre, 2 metre and 3 metre lengths, in each of our timbers and measure 19 mm thick and approximately 70 mm tall.
Pencil Top edge only - £ 8 per metre
Pencil Top and bottom - £ 16 per metre
Bullnose - £ 24 per metre
up to 50 mm - £ 15
51 mm to 250 mm - £ 25
over 250 mm - from £ 35
Overmounted Sink Cutout - £ 75
Undermounted Sink Cutout - £ 125
Undermounted 1 1/2 Bowl Sink Cutout - £ 145
Hob Cutout - £ 75
Whatever kitchen sink you desire, we are able to produce the corresponding sink cutout. Shown here are two typical examples, firstly a stainless steel undermounted sink, shown to the right, in one of our Oak Super Stave worktops, and secondly a ceramic butler sink, shown below, also in our Oak Super Stave.
Drainage Grooves one side of sink - £ 58
Drainage Grooves both sides of sink - £ 116
Solid, brushed steel rods that sit in specially shaped grooves to act as a trivet for hot pans. Hot rods can be easily lifted out of their grooves to allow for cleaning.
£ 16 each including hot rod groove.
Hot rods measure 300 mm long and 12 mm in diameter.
Worktop End Caps protect the ends of your wooden worktop where they meet a constant heat cooker such as an AGA or range cooker. They also provide a great aesthetic finish to the ends of your wooden worktop.
60 mm wide end cap - £ 32
suited to Classic Wide Block worktops
100 mm wide end cap - £ 48
suited to Super Stave and Traditional Plank worktops
End cap fitting - £ 48 per end cap
Please feel free to watch our End Cap Fitting video to the right to see and hear how our joiners attach end caps to our wooden worktops.
Thick, extruded Aluminium sheet that is fixed to the underside of your wooden worktop to protect against any moisture given off from dishwashers and washing machines situated under your wooden worktops.
£ 18 per moisture barrier (one needed per appliance)
Drop down mitre cutting (i.e. 2 x 45 degree cuts) - £ 75
Drop down mitre cuts with joins fullyprepared for assembly on site - £ 115
Drop down mitre full assembly (glued, screwed and plugged) - £ 150
Please note: the worktop and 'drop down' section will arrive fully assemled. Please bear this in mind when considering the room required for manoeuvring the worktop into place.
